Viewing file:  serial.h (10.17 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* linux/include/asm-arm/hardware/serial_amba.h
*
* Internal header file for AMBA serial ports
*
* Copyright (C) ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd.
*/
#ifndef ASM_ARM_HARDWARE_SERIAL_AMBA_H
#define ASM_ARM_HARDWARE_SERIAL_AMBA_H
#ifndef __ASSEMBLY__
#include <linux/bitfield.h>
#include <linux/bits.h>
#endif
#include <linux/types.h>
/* -------------------------------------------------------------------------------
* From AMBA UART (PL010) Block Specification
* -------------------------------------------------------------------------------
* UART Register Offsets.
*/
#define UART01x_DR 0x00 /* Data read or written from the interface. */
#define UART01x_RSR 0x04 /* Receive status register (Read). */
#define UART01x_ECR 0x04 /* Error clear register (Write). */
#define UART010_LCRH 0x08 /* Line control register, high byte. */
#define ST_UART011_DMAWM 0x08 /* DMA watermark configure register. */
#define UART010_LCRM 0x0C /* Line control register, middle byte. */
#define ST_UART011_TIMEOUT 0x0C /* Timeout period register. */
#define UART010_LCRL 0x10 /* Line control register, low byte. */
#define UART010_CR 0x14 /* Control register. */
#define UART01x_FR 0x18 /* Flag register (Read only). */
#define UART010_IIR 0x1C /* Interrupt identification register (Read). */
#define UART010_ICR 0x1C /* Interrupt clear register (Write). */
#define ST_UART011_LCRH_RX 0x1C /* Rx line control register. */
#define UART01x_ILPR 0x20 /* IrDA low power counter register. */
#define UART011_IBRD 0x24 /* Integer baud rate divisor register. */
#define UART011_FBRD 0x28 /* Fractional baud rate divisor register. */
#define UART011_LCRH 0x2c /* Line control register. */
#define ST_UART011_LCRH_TX 0x2c /* Tx Line control register. */
#define UART011_CR 0x30 /* Control register. */
#define UART011_IFLS 0x34 /* Interrupt fifo level select. */
#define UART011_IMSC 0x38 /* Interrupt mask. */
#define UART011_RIS 0x3c /* Raw interrupt status. */
#define UART011_MIS 0x40 /* Masked interrupt status. */
#define UART011_ICR 0x44 /* Interrupt clear register. */
#define UART011_DMACR 0x48 /* DMA control register. */
#define ST_UART011_XFCR 0x50 /* XON/XOFF control register. */
#define ST_UART011_XON1 0x54 /* XON1 register. */
#define ST_UART011_XON2 0x58 /* XON2 register. */
#define ST_UART011_XOFF1 0x5C /* XON1 register. */
#define ST_UART011_XOFF2 0x60 /* XON2 register. */
#define ST_UART011_ITCR 0x80 /* Integration test control register. */
#define ST_UART011_ITIP 0x84 /* Integration test input register. */
#define ST_UART011_ABCR 0x100 /* Autobaud control register. */
#define ST_UART011_ABIMSC 0x15C /* Autobaud interrupt mask/clear register. */
/*
* ZTE UART register offsets. This UART has a radically different address
* allocation from the ARM and ST variants, so we list all registers here.
* We assume unlisted registers do not exist.
*/
#define ZX_UART011_DR 0x04
#define ZX_UART011_FR 0x14
#define ZX_UART011_IBRD 0x24
#define ZX_UART011_FBRD 0x28
#define ZX_UART011_LCRH 0x30
#define ZX_UART011_CR 0x34
#define ZX_UART011_IFLS 0x38
#define ZX_UART011_IMSC 0x40
#define ZX_UART011_RIS 0x44
#define ZX_UART011_MIS 0x48
#define ZX_UART011_ICR 0x4c
#define ZX_UART011_DMACR 0x50
#define UART011_DR_OE BIT(11)
#define UART011_DR_BE BIT(10)
#define UART011_DR_PE BIT(9)
#define UART011_DR_FE BIT(8)
#define UART01x_RSR_OE BIT(3)
#define UART01x_RSR_BE BIT(2)
#define UART01x_RSR_PE BIT(1)
#define UART01x_RSR_FE BIT(0)
#define UART011_FR_RI BIT(8)
#define UART011_FR_TXFE BIT(7)
#define UART011_FR_RXFF BIT(6)
#define UART01x_FR_TXFF (1 << 5) /* used in ASM */
#define UART01x_FR_RXFE BIT(4)
#define UART01x_FR_BUSY (1 << 3) /* used in ASM */
#define UART01x_FR_DCD BIT(2)
#define UART01x_FR_DSR BIT(1)
#define UART01x_FR_CTS BIT(0)
#define UART01x_FR_TMSK (UART01x_FR_TXFF + UART01x_FR_BUSY)
/*
* Some bits of Flag Register on ZTE device have different position from
* standard ones.
*/
#define ZX_UART01x_FR_BUSY BIT(8)
#define ZX_UART01x_FR_DSR BIT(3)
#define ZX_UART01x_FR_CTS BIT(1)
#define ZX_UART011_FR_RI BIT(0)
#define UART011_CR_CTSEN BIT(15) /* CTS hardware flow control */
#define UART011_CR_RTSEN BIT(14) /* RTS hardware flow control */
#define UART011_CR_OUT2 BIT(13) /* OUT2 */
#define UART011_CR_OUT1 BIT(12) /* OUT1 */
#define UART011_CR_RTS BIT(11) /* RTS */
#define UART011_CR_DTR BIT(10) /* DTR */
#define UART011_CR_RXE BIT(9) /* receive enable */
#define UART011_CR_TXE BIT(8) /* transmit enable */
#define UART011_CR_LBE BIT(7) /* loopback enable */
#define UART010_CR_RTIE BIT(6)
#define UART010_CR_TIE BIT(5)
#define UART010_CR_RIE BIT(4)
#define UART010_CR_MSIE BIT(3)
#define ST_UART011_CR_OVSFACT BIT(3) /* Oversampling factor */
#define UART01x_CR_IIRLP BIT(2) /* SIR low power mode */
#define UART01x_CR_SIREN BIT(1) /* SIR enable */
#define UART01x_CR_UARTEN BIT(0) /* UART enable */
#define UART011_LCRH_SPS BIT(7)
#define UART01x_LCRH_WLEN_8 0x60
#define UART01x_LCRH_WLEN_7 0x40
#define UART01x_LCRH_WLEN_6 0x20
#define UART01x_LCRH_WLEN_5 0x00
#define UART01x_LCRH_FEN BIT(4)
#define UART01x_LCRH_STP2 BIT(3)
#define UART01x_LCRH_EPS BIT(2)
#define UART01x_LCRH_PEN BIT(1)
#define UART01x_LCRH_BRK BIT(0)
#define ST_UART011_DMAWM_RX GENMASK(5, 3)
#define ST_UART011_DMAWM_RX_1 FIELD_PREP_CONST(ST_UART011_DMAWM_RX, 0)
#define ST_UART011_DMAWM_RX_2 FIELD_PREP_CONST(ST_UART011_DMAWM_RX, 1)
#define ST_UART011_DMAWM_RX_4 FIELD_PREP_CONST(ST_UART011_DMAWM_RX, 2)
#define ST_UART011_DMAWM_RX_8 FIELD_PREP_CONST(ST_UART011_DMAWM_RX, 3)
#define ST_UART011_DMAWM_RX_16 FIELD_PREP_CONST(ST_UART011_DMAWM_RX, 4)
#define ST_UART011_DMAWM_RX_32 FIELD_PREP_CONST(ST_UART011_DMAWM_RX, 5)
#define ST_UART011_DMAWM_RX_48 FIELD_PREP_CONST(ST_UART011_DMAWM_RX, 6)
#define ST_UART011_DMAWM_TX GENMASK(2, 0)
#define ST_UART011_DMAWM_TX_1 FIELD_PREP_CONST(ST_UART011_DMAWM_TX, 0)
#define ST_UART011_DMAWM_TX_2 FIELD_PREP_CONST(ST_UART011_DMAWM_TX, 1)
#define ST_UART011_DMAWM_TX_4 FIELD_PREP_CONST(ST_UART011_DMAWM_TX, 2)
#define ST_UART011_DMAWM_TX_8 FIELD_PREP_CONST(ST_UART011_DMAWM_TX, 3)
#define ST_UART011_DMAWM_TX_16 FIELD_PREP_CONST(ST_UART011_DMAWM_TX, 4)
#define ST_UART011_DMAWM_TX_32 FIELD_PREP_CONST(ST_UART011_DMAWM_TX, 5)
#define ST_UART011_DMAWM_TX_48 FIELD_PREP_CONST(ST_UART011_DMAWM_TX, 6)
#define UART010_IIR_RTIS BIT(3)
#define UART010_IIR_TIS BIT(2)
#define UART010_IIR_RIS BIT(1)
#define UART010_IIR_MIS BIT(0)
#define UART011_IFLS_RXIFLSEL GENMASK(5, 3)
#define UART011_IFLS_RX1_8 FIELD_PREP_CONST(UART011_IFLS_RXIFLSEL, 0)
#define UART011_IFLS_RX2_8 FIELD_PREP_CONST(UART011_IFLS_RXIFLSEL, 1)
#define UART011_IFLS_RX4_8 FIELD_PREP_CONST(UART011_IFLS_RXIFLSEL, 2)
#define UART011_IFLS_RX6_8 FIELD_PREP_CONST(UART011_IFLS_RXIFLSEL, 3)
#define UART011_IFLS_RX7_8 FIELD_PREP_CONST(UART011_IFLS_RXIFLSEL, 4)
#define UART011_IFLS_TXIFLSEL GENMASK(2, 0)
#define UART011_IFLS_TX1_8 FIELD_PREP_CONST(UART011_IFLS_TXIFLSEL, 0)
#define UART011_IFLS_TX2_8 FIELD_PREP_CONST(UART011_IFLS_TXIFLSEL, 1)
#define UART011_IFLS_TX4_8 FIELD_PREP_CONST(UART011_IFLS_TXIFLSEL, 2)
#define UART011_IFLS_TX6_8 FIELD_PREP_CONST(UART011_IFLS_TXIFLSEL, 3)
#define UART011_IFLS_TX7_8 FIELD_PREP_CONST(UART011_IFLS_TXIFLSEL, 4)
/* special values for ST vendor with deeper fifo */
#define UART011_IFLS_RX_HALF FIELD_PREP_CONST(UART011_IFLS_RXIFLSEL, 5)
#define UART011_IFLS_TX_HALF FIELD_PREP_CONST(UART011_IFLS_TXIFLSEL, 5)
#define UART011_OEIM BIT(10) /* overrun error interrupt mask */
#define UART011_BEIM BIT(9) /* break error interrupt mask */
#define UART011_PEIM BIT(8) /* parity error interrupt mask */
#define UART011_FEIM BIT(7) /* framing error interrupt mask */
#define UART011_RTIM BIT(6) /* receive timeout interrupt mask */
#define UART011_TXIM BIT(5) /* transmit interrupt mask */
#define UART011_RXIM BIT(4) /* receive interrupt mask */
#define UART011_DSRMIM BIT(3) /* DSR interrupt mask */
#define UART011_DCDMIM BIT(2) /* DCD interrupt mask */
#define UART011_CTSMIM BIT(1) /* CTS interrupt mask */
#define UART011_RIMIM BIT(0) /* RI interrupt mask */
#define UART011_OEIS BIT(10) /* overrun error interrupt status */
#define UART011_BEIS BIT(9) /* break error interrupt status */
#define UART011_PEIS BIT(8) /* parity error interrupt status */
#define UART011_FEIS BIT(7) /* framing error interrupt status */
#define UART011_RTIS BIT(6) /* receive timeout interrupt status */
#define UART011_TXIS BIT(5) /* transmit interrupt status */
#define UART011_RXIS BIT(4) /* receive interrupt status */
#define UART011_DSRMIS BIT(3) /* DSR interrupt status */
#define UART011_DCDMIS BIT(2) /* DCD interrupt status */
#define UART011_CTSMIS BIT(1) /* CTS interrupt status */
#define UART011_RIMIS BIT(0) /* RI interrupt status */
#define UART011_OEIC BIT(10) /* overrun error interrupt clear */
#define UART011_BEIC BIT(9) /* break error interrupt clear */
#define UART011_PEIC BIT(8) /* parity error interrupt clear */
#define UART011_FEIC BIT(7) /* framing error interrupt clear */
#define UART011_RTIC BIT(6) /* receive timeout interrupt clear */
#define UART011_TXIC BIT(5) /* transmit interrupt clear */
#define UART011_RXIC BIT(4) /* receive interrupt clear */
#define UART011_DSRMIC BIT(3) /* DSR interrupt clear */
#define UART011_DCDMIC BIT(2) /* DCD interrupt clear */
#define UART011_CTSMIC BIT(1) /* CTS interrupt clear */
#define UART011_RIMIC BIT(0) /* RI interrupt clear */
#define UART011_DMAONERR BIT(2) /* disable dma on error */
#define UART011_TXDMAE BIT(1) /* enable transmit dma */
#define UART011_RXDMAE BIT(0) /* enable receive dma */
#define UART01x_RSR_ANY (UART01x_RSR_OE | UART01x_RSR_BE | UART01x_RSR_PE | UART01x_RSR_FE)
#define UART01x_FR_MODEM_ANY (UART01x_FR_DCD | UART01x_FR_DSR | UART01x_FR_CTS)
#ifndef __ASSEMBLY__
struct amba_device; /* in uncompress this is included but amba/bus.h is not */
struct amba_pl010_data {
void (*set_mctrl)(struct amba_device *dev, void __iomem *base, unsigned int mctrl);
};
struct dma_chan;
struct amba_pl011_data {
bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
void *dma_rx_param;
void *dma_tx_param;
bool dma_rx_poll_enable;
unsigned int dma_rx_poll_rate;
unsigned int dma_rx_poll_timeout;
void (*init)(void);
void (*exit)(void);
};
#endif
#endif
|