Viewing file:  qcom-vadc-common.h (5.54 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/* SPDX-License-Identifier: GPL-2.0 */
/*
* Code shared between the different Qualcomm PMIC voltage ADCs
*/
#ifndef QCOM_VADC_COMMON_H
#define QCOM_VADC_COMMON_H
#include <linux/types.h>
#define VADC_CONV_TIME_MIN_US 2000
#define VADC_CONV_TIME_MAX_US 2100
/* Min ADC code represents 0V */
#define VADC_MIN_ADC_CODE 0x6000
/* Max ADC code represents full-scale range of 1.8V */
#define VADC_MAX_ADC_CODE 0xa800
#define VADC_ABSOLUTE_RANGE_UV 625000
#define VADC_RATIOMETRIC_RANGE 1800
#define VADC_DEF_PRESCALING 0 /* 1:1 */
#define VADC_DEF_DECIMATION 0 /* 512 */
#define VADC_DEF_HW_SETTLE_TIME 0 /* 0 us */
#define VADC_DEF_AVG_SAMPLES 0 /* 1 sample */
#define VADC_DEF_CALIB_TYPE VADC_CALIB_ABSOLUTE
#define VADC_DECIMATION_MIN 512
#define VADC_DECIMATION_MAX 4096
#define ADC5_DEF_VBAT_PRESCALING 1 /* 1:3 */
#define ADC5_DECIMATION_SHORT 250
#define ADC5_DECIMATION_MEDIUM 420
#define ADC5_DECIMATION_LONG 840
/* Default decimation - 1024 for rev2, 840 for pmic5 */
#define ADC5_DECIMATION_DEFAULT 2
#define ADC5_DECIMATION_SAMPLES_MAX 3
#define VADC_HW_SETTLE_DELAY_MAX 10000
#define VADC_HW_SETTLE_SAMPLES_MAX 16
#define VADC_AVG_SAMPLES_MAX 512
#define ADC5_AVG_SAMPLES_MAX 16
#define PMIC5_CHG_TEMP_SCALE_FACTOR 377500
#define PMIC5_SMB_TEMP_CONSTANT 419400
#define PMIC5_SMB_TEMP_SCALE_FACTOR 356
#define PMI_CHG_SCALE_1 -138890
#define PMI_CHG_SCALE_2 391750000000LL
#define VADC5_MAX_CODE 0x7fff
#define ADC5_FULL_SCALE_CODE 0x70e4
#define ADC5_USR_DATA_CHECK 0x8000
#define R_PU_100K 100000
#define RATIO_MAX_ADC7 BIT(14)
/*
* VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
* VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
* calibration.
*/
enum vadc_calibration {
VADC_CALIB_ABSOLUTE = 0,
VADC_CALIB_RATIOMETRIC
};
/**
* struct vadc_linear_graph - Represent ADC characteristics.
* @dy: numerator slope to calculate the gain.
* @dx: denominator slope to calculate the gain.
* @gnd: A/D word of the ground reference used for the channel.
*
* Each ADC device has different offset and gain parameters which are
* computed to calibrate the device.
*/
struct vadc_linear_graph {
s32 dy;
s32 dx;
s32 gnd;
};
/**
* struct vadc_prescale_ratio - Represent scaling ratio for ADC input.
* @num: the inverse numerator of the gain applied to the input channel.
* @den: the inverse denominator of the gain applied to the input channel.
*/
struct vadc_prescale_ratio {
u32 num;
u32 den;
};
/**
* enum vadc_scale_fn_type - Scaling function to convert ADC code to
* physical scaled units for the channel.
* SCALE_DEFAULT: Default scaling to convert raw adc code to voltage (uV).
* SCALE_THERM_100K_PULLUP: Returns temperature in millidegC.
* Uses a mapping table with 100K pullup.
* SCALE_PMIC_THERM: Returns result in milli degree's Centigrade.
* SCALE_XOTHERM: Returns XO thermistor voltage in millidegC.
* SCALE_PMI_CHG_TEMP: Conversion for PMI CHG temp
* SCALE_HW_CALIB_DEFAULT: Default scaling to convert raw adc code to
* voltage (uV) with hardware applied offset/slope values to adc code.
* SCALE_HW_CALIB_THERM_100K_PULLUP: Returns temperature in millidegC using
* lookup table. The hardware applies offset/slope to adc code.
* SCALE_HW_CALIB_XOTHERM: Returns XO thermistor voltage in millidegC using
* 100k pullup. The hardware applies offset/slope to adc code.
* SCALE_HW_CALIB_THERM_100K_PU_PM7: Returns temperature in millidegC using
* lookup table for PMIC7. The hardware applies offset/slope to adc code.
* SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
* The hardware applies offset/slope to adc code.
* SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
* The hardware applies offset/slope to adc code. This is for PMIC7.
* SCALE_HW_CALIB_PM5_CHG_TEMP: Returns result in millidegrees for PMIC5
* charger temperature.
* SCALE_HW_CALIB_PM5_SMB_TEMP: Returns result in millidegrees for PMIC5
* SMB1390 temperature.
*/
enum vadc_scale_fn_type {
SCALE_DEFAULT = 0,
SCALE_THERM_100K_PULLUP,
SCALE_PMIC_THERM,
SCALE_XOTHERM,
SCALE_PMI_CHG_TEMP,
SCALE_HW_CALIB_DEFAULT,
SCALE_HW_CALIB_THERM_100K_PULLUP,
SCALE_HW_CALIB_XOTHERM,
SCALE_HW_CALIB_THERM_100K_PU_PM7,
SCALE_HW_CALIB_PMIC_THERM,
SCALE_HW_CALIB_PMIC_THERM_PM7,
SCALE_HW_CALIB_PM5_CHG_TEMP,
SCALE_HW_CALIB_PM5_SMB_TEMP,
SCALE_HW_CALIB_INVALID,
};
struct adc5_data {
const u32 full_scale_code_volt;
const u32 full_scale_code_cur;
const struct adc5_channels *adc_chans;
const struct iio_info *info;
unsigned int *decimation;
unsigned int *hw_settle_1;
unsigned int *hw_settle_2;
};
int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
const struct vadc_linear_graph *calib_graph,
const struct vadc_prescale_ratio *prescale,
bool absolute,
u16 adc_code, int *result_mdec);
struct qcom_adc5_scale_type {
int (*scale_fn)(const struct vadc_prescale_ratio *prescale,
const struct adc5_data *data, u16 adc_code, int *result);
};
int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
unsigned int prescale_ratio,
const struct adc5_data *data,
u16 adc_code, int *result_mdec);
u16 qcom_adc_tm5_temp_volt_scale(unsigned int prescale_ratio,
u32 full_scale_code_volt, int temp);
int qcom_adc5_prescaling_from_dt(u32 num, u32 den);
int qcom_adc5_hw_settle_time_from_dt(u32 value, const unsigned int *hw_settle);
int qcom_adc5_avg_samples_from_dt(u32 value);
int qcom_adc5_decimation_from_dt(u32 value, const unsigned int *decimation);
int qcom_vadc_decimation_from_dt(u32 value);
#endif /* QCOM_VADC_COMMON_H */
|